CC Series
Maximum convenience – assembly without turning or rotating
Force-fit connections between engine, cardan shaft and rotor make pumps of the CC series particularly easy to assemble. Precise positioning of parts to one another like with involute, fitting key or pin joint connections is not required. The cone joint is also self-centering and can simply be clamped or released via a threaded rod. Tedious removal of small pins in a narrow suction housing or similar work is not required.
Advantages of the Vogelsang drive concept:
- Self-centering cone joints
- No need to turn the halves of the joint so they are precisely positioned to one another
- Simple release and clamping via an easily accessible threaded rod
From the back or the front: open, grip, replace
Instead of having to disassemble stator, rotor and cardan shaft, the seals of CC series progressive cavity pumps can be also be replaced from the drive side. The parallel shaft geared motor is simply removed for this. The seal is then replaced with just a few turns of the hand. Of course, it can also be changed through the pumping chamber after dismounting the cardan shaft.
Complete seal set – professional, practical and reliable
Seals of CC series pumps can be replaced in just one single step, significantly simplifying maintenance while also lowering the risk of gear damage. As a fully pre-installed mechanical seal in cartridge design, the Quality Cartridge from Vogelsang complies with the highest factory-tested safety standards, runs with minimal problems, and installs quickly. All seal components are assembled automatically in the factory and complete sets undergo a computer-aided check so that they can be replaced simply and quickly on site. No expensive special tools are necessary.
Advantages of the Quality Cartridge at a glance:
- Simple and safe replacement of seals, avoiding assembly mistakes
- Saves time compared to conventional sealing changes
Double the assurance – tough quality, resistance to disruptions design
The generously sized cardan shaft of the CC series also ensures smooth running. Drive power is reliably transferred from the parallel shaft geared motor to the rotor by two robust cardan joints. By means of a tough-wearing sleeve, the cardan shaft is protected from contact with the pump medium and therefore from solid and fibrous matter within it that can cause malfunctions. At the same time, the smooth surface and constant cross section of the cardan shaft ensure that no solids adhere or wind up fibers and lead to blockages. In case of any service work on the stator, rotor or seal there is no need to touch the cardan shaft at any time. This rules out defects due to assembly mistakes.
Advantages of the Vogelsang cardan shaft:
- Generously dimensioned cardan shaft increases lifetime
- Tough sleeve for protection of the cardan shaft
- Prevention of blockages due to smooth surfaces and consistent cross-section
What a turnaround – replacement without removal
Pumps of the CC series have a diagonal flange connection on the pressure side. This simple but ultimately clever design concept, enabling the rotor/stator unit, after removal of a few screws, to be simply swiveled to the side or up. At the same time the pump remains permanently screwed into the piping on both suction and pressure side, removing the need to fixate or support the pipework.
Advantages of the Vogelsang swiveling mechanism
- The rotor and stator can be simply swiveled out as a single unit
- The pump remains permanently screwed into the pipework for service and maintenance
A service sensation: Easier, faster, more effective
With unique CC series progressive cavity pumps, long downtimes for service and maintenance will finally be a thing of the past. Thanks to the innovative design, rotor and stator can be replaced as a single unit quickly and simply meaning the pump is ready for operation within a short time. The innovative drive concept and the smart swiveling mechanism allow fast and simple replacement of parts without disassembly from the pipework. If needed, the entire rotating unit (stator, rotor and cardan shaft) can also be exchanged within the shortest of times or else only the stator replaced.
Advantages of the QuickService design:
- Easy and quick service with a highly compact footprint
- No need to disassemble pressure/suction pipe
No space problems – service and maintenance without disassembly of the line
CC series pumps remain securely screwed in the pipework when the pumping elements are replaced. There is no need to disassemble parts of the pressure-side line and less space is needed during maintenance work. Just 300 mm are all that is required to replace the rotor/stator unit with ease.
Work simplification – less single parts, less work
To remove the rotor/stator unit from one CC series pump, the screws just need to be removed from two flange connections and the central hexagon nut detached. There are no more single parts than this. And reassembling the pump is just as simple of course.
A matter of design – the right pump for the every application
QuickService CC series progressive cavity pumps are available in four sizes with a pumping capacity of up to 300 m3/h. Three different rotor/stator geometries enable pressures of up to 12 bar. As an economical solution for clogging-free pumping, CC series pumps are available with a flow-optimized StreamLine suction housing. If the pump is to be connected to several pipes, we recommend the MultiConnect suction housing. Optionally with integrated heavy material separator for holding back stones and metal parts contained in the medium. Numerous additional options also enable configuration that is specially coordinated to the application.